The VLT® AQUA Drive is designed to provide the highest level of performance of AC-motor-driven water and wastewater applications. Featuring a wide range of powerful standard features, which can be expanded with performance-improving options, the drive is equally suited to both new and retrofit projects. The considerable daily load variation in water or wastewater treatment plants makes it economically feasible to introduce motor control on rotating equipment such as pumps and blowers. The new generation VLT AQUA Drive can realistically offer first-year cost savings of between 10–30% compared to traditional drive solutions. Its high lifetime availability and low energy consumption and maintenance costs provide you with the lowest cost of ownership.
The quick and user-friendly setup of water and pump settings reduces installation time ensuring a fast route to maximum energy efficiency and motor control. By collecting the most important parameters in one place, the risk of incorrect configuration is reduced significantly.
• 5000 / 5000 FLUX / 6000 HVAC / 8000 AQUA ® Operating Instructions Profibus DP V1 Drives Solutions www.danfoss.com/drives. • SYNC and FREEZE...22 SYNC/UNSYNC...
VLT® 8000 AQUA General technical. 16 MG.80.A2.02 - VLT is a registered Danfoss trademark. VLT® 5000/5000 FLUX/6000 HVAC/8000 AQUA. Documentation within this manual, Danfoss A/S. The series VLT 5000/VLT 5000 Flux/VLT 6000 HVAC/VLT 8000 AQUA by DANFOSS.
22 FREEZE/UNFREEZE...22 Control word/Status word..23 Control word/Status word..23 Control word according to profidriveprofile..23 Status word according to profidriveprofile.. 25 MG.90.G1.02 - VLT is a registered Danfoss trademark.
• Warning word, extended Status word and Alarm word.. 44 Station address... 46 Extended Diagnosis...47 Parameter list...48 Appendix...58 Glossar... 58 Abbreviations used...59 MG.90.G1.02 - VLT is a registered Danfoss trademark. • 175Z4207 (uncoated) laws of Denmark and most other countries.
175Z4208 (coated) It is NOT possible to run FMS from a VLT 5000 Danfoss A/S does not warrant that a software program FLUX or a VLT 8000 AQUA. Produced according to the guidelines provided in.
• 8000 AQUA PROFIBUS Assumptions Even if you are an experienced PROFIBUS programmer, The manual assumes that you are using a DANFOSS we suggest that you read this manual in its entirety PROFIBUS DP option card, together with a DANFOSS before you start programming, since important VLT frequency converter, that you are using a PLC or information can be found in all chapters. • PPO is defined as a connected module. The frequency converter parameters may be gathered from parameter interface (PCV, length of 8 bytes) of the the manual for the VLT 5000/VLT 5000 FLUX/VLT PPO always has module consistency. 6000 HVAC/VLT 8000 AQUA series. How To Program Rsview32 Ebook. • A master may be a PLC or a PC that is equipped with a PROFIBUS communication card.
MG.90.G1.02 - VLT is a registered Danfoss trademark. • Parameter up-/downloads can be achieved by using the PCV part of the so-called Parameter - Process data Objects - PPO types 1, 2 or 5, see drawing in paragraph PPO description. MG.90.G1.02 - VLT is a registered Danfoss trademark. • After that, the token is handled back to the MC 1, and a new DP cycle is started. MC1: Master Class 1 MG.90.G1.02 - VLT is a registered Danfoss trademark. • 128 nodes (3 repeater, frequency converters) 61 frequency 91 frequency 121 frequency converters) [m] converters) [m] converters) [m] 9.6-187.5 kBaud 1000 2000 3000 4000 500 kBaud 1200 1600 1.5 MBaud 3-12 MBaud MG.90.G1.02 - VLT is a registered Danfoss trademark. • - Wire type: twisted pair, 1 x 2 or 2 x 2 or 1 x 4 conductors - Shielding copper-braided or braided and foil laminated Segment 1 Segment 2 Segment 3 Segment 4 MG.90.G1.02 - VLT is a registered Danfoss trademark.
• PROFIBUS network. Additional notes concerning the subject of EMC can be found in the project manual for the VLT 5000 series (MG.50.Cx. Geekbench 2 Ipa. yy) Bus connection and in the manual for the Profibus master. • - If an internal termination circuit in the form of three resistors is connected to the bus line, a 5 V direct voltage must be used. Attention: please make sure that it is voltaically separated from the power supply cable.
MG.90.G1.02 - VLT is a registered Danfoss trademark. • Blinking, when the function for the automatic baud rate determination attempts to determine the current baud rate. Note: a faulty connection of the data line may also cause blinking of the LEDs. (see 'Physical connection'). MG.90.G1.02 - VLT is a registered Danfoss trademark. • The modification of the address switches occurs during the next turn-on procedure. See also section Station Address.