Answer Yes, you can run AVR Studio with your configuration. The only issue is the version of Windows which you have installed on your system, as AVR 6 is compatible with Windows XP (SP 3), but only. With the 32-bit version. Also, if you have the 64-bit version of the software, you should have 2 GG of RAM installed on your machine.

You should consider upgrading your operating system as Windows XP will constantly lose support from software developers. You can check the system requirements for AVR by accessing Atmel's website. Official website: http://www.atmel.com/webdoc/atmelstudio/atmelstudio.Introduction.InstallationUpdate.Requirements.html.

Hello, I'm new to this forum and I tried unsuccessfully to locate a similar question. I'm hoping someone can help.

I recently purchased an ATMEL development system (i.e. Mana Bars 1.26a there. Programmer) to program microcontrollers. When I first plugged this programmer into the USB of my PC, it automatically installs a USB plug & play driver called 'Jungo Connectivity'. According to the ATMEL discussion groups, this driver sometimes doesn't install correctly on the 1st attempt, needs to be removed and re-installed. When I go into the Device Manager, I can see an entry for 'Jungo Connectivity' which has a drop-down arrow beside it.

When I view the contents of Jungo, I see another driver called 'WinDriver'. I can easily right-click to uninstall WinDriver but not Jungo Connectivity. I assumed this might be enough to allow the driver to automatically install when I restart my PC and plug in the programmer but this is unfortunately not the case. I assume that I did not sufficiently remove all the driver components to trick my PC to re-installing the drivers as though this was my 1st attempt. Can anyone tell me how I can purge all the remnants of these drivers so that I can attempt a successful re-install? Thanks for taking the time to read through my question.

Hello Dean, Thank you for posting your question on Microsoft Community. I would like to know some information about the issue so that we could help you better. Does Jungo connectivity appear under Universal Bus service(USB) devices? Is the issue specific to this device? I would suggest you to try following methods and check if it helps. Method 1: Please run these Microsoft Fixit and check the issue.

Hardware devices are not working or are not detected in Windows Diagnose and fix Windows USB problems automatically If it does not help, then use steps in method 2. Method 2: Disconnect all USB devices and then perform the following steps: a. Click Start, and then click Control Panel. Click System and Maintenance, click System, and then click Device Manager. Note: If Control Panel is in Classic View, double-clickSystem, and then click Device Manager. If you are prompted for an administrator password or for a confirmation, type the password, or click Allow. In Device Manager, double click to expand 'Universal Serial Bus controllers', right click on the Host Controller, click 'Uninstall' and click 'OK'.

Here you can download free sci android usb driver jungo v4 shared files found in our database: SCI android usb driver jungo v4.7z from mediafire.com host micromax-a67. Jungo Driver Update Utility Free Download. Keep your Jungo drivers up to date automatically.

Check if at all there is an exclamation mark along the driver, it suggests issues with the driver installed. Repeat the step 2 to uninstall all items under 'Universal Serial Bus controllers'. Then, restart your computer and Windows 7 will reinstall all USB controllers automatically. If issue still persists, then use suggestions in article given in method 3.

Method 3: Tips for solving problems with USB devices (also applies to Windows 7) I would also suggest you to update chipset drivers of your computer from manufacturer's website. Refer: Update a driver for hardware that isn't working properly I hope this information helps.

Please do let us know if you need any further assistance. Hello Ratandeep, Thank you for your quick response. I attempted Method's 1 & 2 with no luck. As for your questions, this is only an issue with this particular device. The description from the provider of the hardware (ATMEL) is shown at this link: The drivers for 'JTAGICE3' and 'WinDriver' are supposed to show up under 'Jungo'.

Instead, I have only 'WinDriver' under 'Jungo'. When I plug in the JTAGICE3 hardware into my USB, I notice a new USB device appear under the 'Universal Serial Bus Controllers', called a 'USB Composite Device'. On the Link I provided from ATMEL, at the bottom of that page, they state the following: Note Firmware version 3 and later uses a HID interface for communication. The USB driver provided by the operating system is loaded automatically in this case. Is it possible that I am not getting the anticipated response as illustrated in their description because Windows is loading this as an 'HID' device? In either case, I'm still not getting communication between my PC and this programmer. Thanks, Dean.